# generated by Slic3r 1.1.7 on Fri Apr 10 13:37:24 2015 avoid_crossing_perimeters = 1 bed_size = 160,160 bed_temperature = 0 bottom_solid_layers = 3 bridge_acceleration = 1000 bridge_fan_speed = 100 bridge_flow_ratio = 1 bridge_speed = 60 brim_width = 0 complete_objects = 0 cooling = 1 default_acceleration = 2000 disable_fan_first_layers = 1 dont_support_bridges = 1 duplicate_distance = 6 end_gcode = M400\nM104 S0 ; Hotend off\nM140 S0 ; heated bed heater off (if you have it)\nM107 ; fans off\nG92 E0 ; set extruder to 0\nG1 E-3 F300 ; retract a bit to relieve pressure\nG1 X5 Y5 Z156 F10000 ; move to cooling positioning\nM190 R60 ; wait for bed to cool\nM140 S0 ; turn off bed temp\nG1 X145 Y175 Z156 F1000 ; move to cooling positioning\nM84 ; steppers off\nG90 ; absolute positioning\n;{profile_string} external_perimeter_speed = 70% external_perimeters_first = 0 extra_perimeters = 1 extruder_clearance_height = 20 extruder_clearance_radius = 20 extruder_offset = 0x0 extrusion_axis = E extrusion_multiplier = 1 extrusion_width = 0.5 fan_always_on = 0 fan_below_layer_time = 60 filament_diameter = 3 fill_angle = 45 fill_density = 10% fill_pattern = honeycomb first_layer_acceleration = 500 first_layer_bed_temperature = 0 first_layer_extrusion_width = 200% first_layer_height = 0.425 first_layer_speed = 30% first_layer_temperature = 0 g0 = 0 gap_fill_speed = 20 gcode_arcs = 0 gcode_comments = 0 gcode_flavor = reprap infill_acceleration = 2500 infill_every_layers = 1 infill_extruder = 1 infill_extrusion_width = 0.6 infill_first = 0 infill_only_where_needed = 0 infill_speed = 60 interface_shells = 0 layer_gcode = layer_height = 0.25 max_fan_speed = 100 min_fan_speed = 35 min_print_speed = 10 min_skirt_length = 15 notes = nozzle_diameter = 0.5 only_retract_when_crossing_perimeters = 1 ooze_prevention = 0 output_filename_format = [input_filename_base].gcode overhangs = 1 perimeter_acceleration = 1000 perimeter_extruder = 1 perimeter_extrusion_width = 0.45 perimeter_speed = 40 perimeters = 3 post_process = print_center = 80,80 raft_layers = 0 resolution = 0 retract_before_travel = 2 retract_layer_change = 1 retract_length = 1 retract_length_toolchange = 10 retract_lift = 0.2 retract_restart_extra = 0 retract_restart_extra_toolchange = 0 retract_speed = 10 seam_position = aligned skirt_distance = 3 skirt_height = 1 skirts = 1 slowdown_below_layer_time = 30 small_perimeter_speed = 30 solid_fill_pattern = rectilinear solid_infill_below_area = 70 solid_infill_every_layers = 0 solid_infill_extrusion_width = 0.5 solid_infill_speed = 60 spiral_vase = 0 standby_temperature_delta = -5 start_gcode = ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}\n;Print time: {print_time}\n;Filament used: {filament_amount}m {filament_weight}g\n;Filament cost: {filament_cost}\nG21 ; metric values\nG90 ; absolute positioning\nM82 ; set extruder to absolute mode\nM107 ; start with the fan off\nG92 E0 ; set extruder position to 0\nM140 S100 ; get bed heating up\nG28 ; home all\nM109 S150 ; set to cleaning temp and wait\nG1 Z150 E-30 F75 ; suck up XXmm of filament\nM109 S170 ; heat up rest of way\nG1 X45 Y174 F11520 ; move behind scraper\nG1 Z0 F1200 ; CRITICAL: set Z to height of top of scraper\nG1 X45 Y174 Z-.5 F4000 ; wiping ; plunge into wipe pad\nG1 X55 Y172 Z-.5 F4000 ; wiping\nG1 X45 Y174 Z0 F4000 ; wiping\nG1 X55 Y172 F4000 ; wiping\nG1 X45 Y174 F4000 ; wiping\nG1 X55 Y172 F4000 ; wiping\nG1 X45 Y174 F4000 ; wiping\nG1 X55 Y172 F4000 ; wiping\nG1 X60 Y174 F4000 ; wiping\nG1 X80 Y172 F4000 ; wiping\nG1 X60 Y174 F4000 ; wiping\nG1 X80 Y172 F4000 ; wiping\nG1 X60 Y174 F4000 ; wiping\nG1 X90 Y172 F4000 ; wiping\nG1 X80 Y174 F4000 ; wiping\nG1 X100 Y172 F4000 ; wiping\nG1 X80 Y174 F4000 ; wiping\nG1 X100 Y172 F4000 ; wiping\nG1 X80 Y174 F4000 ; wiping\nG1 X100 Y172 F4000 ; wiping\nG1 X110 Y174 F4000 ; wiping\nG1 X100 Y172 F4000 ; wiping\nG1 X110 Y174 F4000 ; wiping\nG1 X100 Y172 F4000 ; wiping\nG1 X110 Y174 F4000 ; wiping\nG1 X115 Y172 Z-0.5 F1000 ; wipe slower and bury noz in cleanish area\nG1 Z10 ; raise z\nG28 X0 Y0 ; home x and y\nM109 S170 ; set to probing temp\nM204 S300 ; set accel for probing\nG29 ; Probe\nM204 S2000 ; set accel back to normal\nG1 X5 Y15 Z10 F5000 ; get out the way\nM400 ; clear buffer\nG4 S1 ; pause\nM109 S235 ; set extruder temp and wait\nG4 S25 ; wait for bed to temp up\nG1 Z2 E0 F75 ; extrude filament back into nozzle\nM140 S100 ; get bed temping up during first layer support_material = 0 support_material_angle = 0 support_material_enforce_layers = 0 support_material_extruder = 1 support_material_extrusion_width = 0.4 support_material_interface_extruder = 1 support_material_interface_layers = 3 support_material_interface_spacing = 0 support_material_interface_speed = 100% support_material_pattern = pillars support_material_spacing = 2.5 support_material_speed = 60 support_material_threshold = 0 temperature = 0 thin_walls = 1 threads = 2 toolchange_gcode = top_infill_extrusion_width = 0.3 top_solid_infill_speed = 50 top_solid_layers = 4 travel_speed = 175 use_firmware_retraction = 0 use_relative_e_distances = 0 vibration_limit = 0 wipe = 0 z_offset = 0